Full NACE-CIP2-001 Practice Test and 100 Unique Questions, Get it Now!
The Best NACE-CIP2-001 Exam Study Material Premium Files and Preparation Tool
NEW QUESTION # 39
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. Fusion Bonded Epoxy
- C. 2-Layer Polyethylene (PE)
- D. 3-Layer Polyethylene (PE)
Answer: D
NEW QUESTION # 40
The Inspectors' goal at the Pre-Job Conference is to:
- A. Manage the meeting so it doesn't go off topic
- B. Discuss contractual requirements
- C. Obtain a clear understanding of the Specification
- D. Take accurate meeting minutes for distribution
Answer: C
NEW QUESTION # 41
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. is typically green or led and looks like "painted" finish.
Answer: B
NEW QUESTION # 42
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Advise the coating applicator supervisor of your readings
- B. Document the readings at the end of the shift
- C. Check to See if the dehumidification equipment is operating correctly
- D. Call your supervisor
Answer: A
NEW QUESTION # 43
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Stoning
- B. High-pressure water washing
- C. Sacking
- D. Acid etching
Answer: D
NEW QUESTION # 44
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. Risk of chemical exposure
- C. Risk of acid or caustic splashes
- D. a), b), and c)
Answer: D
NEW QUESTION # 45
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Steam cleaning only
- D. Watterjetting only
Answer: B
NEW QUESTION # 46
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Stop the job immediately
- C. Consult the specification to determine how they should be treated
- D. Write an NCR and call the fabricator
Answer: C
NEW QUESTION # 47
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Ultra Sonic DFT Gauge
- C. Magnetic Gauge
- D. Eddy Current Gauge
Answer: A
NEW QUESTION # 48
Inspector reports should always be copied to:
- A. The Owner only
- B. All parties involved in the project
- C. Whomever the Owner identifies
- D. The Contractor and Owner
Answer: C
NEW QUESTION # 49
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. linings protect the contents and the container.
- C. coatings are more durable than linings.
- D. coatings are expected to degrade over time.
Answer: B
NEW QUESTION # 50
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. provide worker comfort.
- C. lower its dew point,
- D. raise its relative humidity.
Answer: C
NEW QUESTION # 51
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A destructive paint inspection Tooke gauge
- C. A mechanical adhesion tester
- D. A set of 14 pencils of varying hardness
Answer: B
NEW QUESTION # 52
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 53
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. dirt.
- C. mill scale.
- D. snow, ice or water.
Answer: C
NEW QUESTION # 54
All of these are advantages of using repair patches EXCEPT
- A. excellent abrasion resistance.
- B. barrier to moisture and corrosion.
- C. inert to common acids, alkalis, and solvents.
- D. special tools or equipment are required.
Answer: D
NEW QUESTION # 55
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Request that the Contractor re-blast the floor
- C. Review the standard with the Contractor and re-inspect the floor
- D. Call your supervisor
Answer: C
NEW QUESTION # 56
NACE International Standards are developed by:
- A. Standard committees
- B. International mandates
- C. Regional mandates
- D. Government mandates
Answer: A
NEW QUESTION # 57
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION # 58
......
Get Instant Access to NACE-CIP2-001 Practice Exam Questions: https://www.testbraindump.com/NACE-CIP2-001-exam-prep.html
Reliable Study Materials & Testing Engine for NACE-CIP2-001 Exam Success!: https://drive.google.com/open?id=1MY6iTnA9np0nx1zCX0QQHqgcUHrFuxsO
