[Dec-2024] Feel EMC D-PCM-DY-23 Dumps PDF Will likely be The best Option
D-PCM-DY-23 exam torrent EMC study guide
NEW QUESTION # 29
Match the DSCP class selectors with their description.
Answer:
Explanation:
NEW QUESTION # 30
Which L3 feature overrides routing protocol decisions and determines the forwarding of packets?
- A. PBR
- B. SMTP
- C. RSTP
- D. SVI
Answer: A
NEW QUESTION # 31
An administrator just finished configuring a Dell EMC N-Series switch. After rebooting the switch, the administrator notices that all the configuration settings just entered are gone.
Which command did the administrator fail to enter?
- A. Copy running-config startup-config
- B. Copy running-config backup-config
- C. Copy startup-config running-config
- D. Copy startup-config backup-config
Answer: A
NEW QUESTION # 32
You are configuring VRRP on a group of Dell EMC Campus networking switches. In addition to redundancy, you need to minimize any down times or disruptions on the network.
Which configuration step can be performed to help meet this requirement?
- A. Disable VRRP preempt on only the switch configured with the highest priority
- B. Configure all VRRP group members with the same priority so they share the Master role
- C. Disable VRRP preempt on all VRRP group members
- D. Increase the VRRP advertise-interval on all VRRP group members
Answer: C
NEW QUESTION # 33
A switch has the following IP configuration:
- VLAN10: IP address 192.168.10.1/24
- VLAN20: IP address 192.168.20.1/24
- VLAN30: IP address 192.168.30.1/24
and the following routes:
0.0.0.0/0 192.168.10.10
10.0.0.0/8 192.168.20.10
A packet with source 192.168.30.10 and destination 10.10.10.10 matches a policy-based routing clause using the set default next-hop 192.168.10.2 parameter.
What is next hop that will be used by the switch to forward the packet?
- A. 192.168.10.2
- B. 192.168.10.10
- C. 10.10.10.10
- D. 192.168.20.10
Answer: D
NEW QUESTION # 34
A network administrator added a new Dell EMC N-Series switch into their network with RSTP configured. The spanning-tree priority on all existing switches has been left at the default value.
If the administrator wants this new switch to become the spanning tree root, which command should be used?
- A. spanning-tree priority 32768
- B. spanning-tree priority 61440
- C. spanning-tree priority 36864
- D. spanning-tree priority 4096
Answer: D
NEW QUESTION # 35
Which packet characteristics can policy-based routing be configured to match against?
- A. L3 Packet Length, TTL, and 802.1p Priority
- B. TTL, TCP Port, and L3 Packet Length
- C. TCP Port, L3 Packet Length, and 802.1p Priority
- D. TCP Port, TTL, and 802.1p Priority
Answer: C
NEW QUESTION # 36
A network administrator wants different applications' traffic to take different network paths.
Which information can the administrator use to create a match to differentiate the application traffic when using policy-based routing?
- A. Physical port number
- B. Source IP address
- C. Application TCP port number
- D. Destination IP address
Answer: C
NEW QUESTION # 37
Which password features are recommended when configuring local users on a Dell EMC N-Series switch?
- A. Password strength-check and Password aging
- B. Password lock-out and Password strength-check
- C. Password min-length and Password history
- D. Password aging and Password lock-out
Answer: B
NEW QUESTION # 38
What is a recommended configuration for an MLAG peer-link on a Dell EMC N-Series switch?
- A. Link must contain multiple interfaces
- B. Spanning tree must be disabled
- C. Link must be a trunk port
- D. Spanning tree must be enabled
Answer: D
NEW QUESTION # 39
A Dell EMC N-Series switch is configured with switchport mode access and ingress filtering.
What is the purpose of ingress filtering?
- A. Allow the port to accept only untagged frames in the configured VLAN
- B. Allow the port to transmit only untagged frames in the configured VLAN
- C. Allow the port to transmit both tagged and untagged frames in the configured VLAN
- D. Allow the port to accept both tagged and untagged frames in the configured VLAN
Answer: D
NEW QUESTION # 40
Which Layer 2 network protocol is used for automatic configuration of switch VLANs and dynamically manages VLAN membership on trunk ports?
- A. MSTP
- B. GVRP
- C. RSTP
- D. PVST
Answer: B
NEW QUESTION # 41
When setting up VoIP, you decide that you want to use LLDP. LLDP is enabled by default and LLDP Transmit Management Information and Notification modes are enabled.
What additional steps need to be performed?
- A. Enable ISDP and enable LLDP-MED confignotification
- B. Disable ISDP and enable LLDP-MED confignotification
- C. Enable ISDP and disable LLDP-MED confignotification
- D. Disable ISDP and disable LLDP-MED confignotification
Answer: B
NEW QUESTION # 42
Why would a network administrator select MLAG for two switches versus stacking?
- A. MLAG switches have a shared management IP address.
- B. MLAG switches can be upgraded independently from each other.
- C. MLAG switches can have VLANs with both redundant and non-redundant ports.
- D. MLAG is compatible with Cisco vPC and VSS, and OS10 VLT.
Answer: B
NEW QUESTION # 43
When using LLDP for configuration communication, what additional protocol features should be enabled to allow the switch to share all VoIP related parameters?
- A. lldp med confignotification, lldp transmit-tlv sys-cap, and lldp transmit-mgmt
- B. lldp transmit-tlv sys-cap, lldp med confignotification, and lldp notification
- C. lldp notification, lldp transmit-mgmt, and lldp transmit-tlv sys-cap
- D. lldp transmit-mgmt, lldp notification, and lldp med confignotification
Answer: D
NEW QUESTION # 44
When DSCP is used for QoS prioritization, which type of service is typically used for voice traffic?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 45
A user's workstation has an IP phone connected to a Dell EMC N-Series switch.
What is the recommended number of VLANs that should be configured on the switch port?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 46
What is the interaction between CDP, ISDP, and LLDP when communicating configuration information from a Dell EMC Campus networking switch to a Cisco VoIP phone?
- A. N-Series switches can be configured to use ISDP or CDP to communicate configuration information with Cisco devices
- B. N-Series switches can be configured to use only CDP to communicate configuration information with Cisco devices
- C. N-Series switches can be configured to use LLDP or CDP to communicate configuration information with Cisco devices
- D. N-Series switches can be configured to use ISDP or LLDP to communicate configuration information with Cisco devices
Answer: D
NEW QUESTION # 47
How many ACLs are supported on a single interface in Dell EMC switches?
- A. One ACL in either direction
- B. Two ACLs in either direction
- C. No limit of ACLS per interface
- D. One ACL in only one direction
Answer: A
NEW QUESTION # 48
A network administrator wants the traffic on different applications to take different network paths.
Which information can the administrator use to create a match to differentiate the application traffic when using policy-based routing?
- A. Physical port number
- B. TCP port number
- C. Source IP address
- D. Destination IP address
Answer: B
NEW QUESTION # 49
When configuring a PBR route-map, what are the configurable "SET" options?
- A. set ip next-hop, set ip default next-hop, and set ip precedence
- B. set ip source, set ip next-hop, and set ip default next-hop
- C. set ip next-hop, set ip source, and set ip precedence
- D. set ip source, set ip default next-hop and set ip precedence
Answer: A
NEW QUESTION # 50
Which command will show the policy-based routing map applied on an interface?
- A. show ip interface
- B. show ip access-lists
- C. show ip policy
- D. show route-map
Answer: C
NEW QUESTION # 51
You are tasked with deploying a single Dell EMC N-Series switch with a 2-port port-channel to uplink to an existing upstream switch.
The following reflects the upstream switch configuration:
- N4032F#show running-config interface tengigabitethernet 1/0/5 channel-group 1 mode on
- N4032F#show running-config interface tengigabitethernet 1/0/6 channel-group 1 mode on Which type of port-channel should be configured to successfully uplink?
- A. Active
- B. Passive
- C. MLAG
- D. Static
Answer: D
NEW QUESTION # 52
Which two centralized authentication and authorization methods are available for Dell PowerSwitches? (Select 2)
- A. TACACS
- B. LDAP
- C. Active Directory
- D. RADIUS
Answer: A,D
NEW QUESTION # 53
......
Use Valid New D-PCM-DY-23 Test Notes & D-PCM-DY-23 Valid Exam Guide: https://www.testbraindump.com/D-PCM-DY-23-exam-prep.html
D-PCM-DY-23 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://drive.google.com/open?id=1ch8tIoSL4kiZKXVxeqLwdJIvJRowuD0c
