Latest [Dec 30, 2021] NACE NACE-CIP1-001 Exam Practice Test To Gain Brilliante Result
Take a Leap Forward in Your Career by Earning NACE NACE-CIP1-001
NEW QUESTION 38
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. are used to measure temperature from a distance.
Answer: A
NEW QUESTION 39
ISO SA 2.5 is defined as:
- A. Very Thorough Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Light Blast Cleaning
Answer: A
NEW QUESTION 40
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 1 cm (.39 inch)
- C. 2.5 cm (1 inch)
- D. 2.5 millimeters (.10 inch)
Answer: C
NEW QUESTION 41
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. cracking.
- B. checking.
- C. holiday.
- D. sagging.
Answer: C
NEW QUESTION 42
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Tanks and Vessels to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Stainless steel pipe to be Externally Coated
Answer: C
NEW QUESTION 43
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Advise the Contractor he cannot proceed
- C. Call your supervisor
- D. Advise the Contractor he can proceed
Answer: A
NEW QUESTION 44
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Blotter test
- C. Needle pressure gauge
- D. Psychrometer
Answer: A
NEW QUESTION 45
Most industrial coatings are:
- A. Organic
- B. Inorganic
- C. Resistant to concentrated sulfuric acid
- D. Resistant to temperatures above 200C
Answer: A
NEW QUESTION 46
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Harden and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and return to its original hardness when cooled
Answer: C
NEW QUESTION 47
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Localized Corrosion
- B. Galvanic Corrosion
- C. General Corrosion
- D. Atmospheric Corrosion
Answer: B
NEW QUESTION 48
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Hire a third patty to assist you in understanding the document
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Carefully review the document and do the best you can
- D. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
Answer: C
NEW QUESTION 49
The NACE Inspector should perform tests for soluble salts:
- A. Prior to surface preparation
- B. Prior to coating application
- C. When specified
- D. After surface preparation
Answer: C
NEW QUESTION 50
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- D. Purchase Professional Liability Insurance prior to job commencement
Answer: A
NEW QUESTION 51
The most important factor resulting in improved job site safety is:
- A. Engineering Controls
- B. Personal Protective Equipment
- C. Safety Enforcement
- D. Situational Awareness
Answer: D
NEW QUESTION 52
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Failing to determine the base metal reading (BMR)
- B. Measuring ditty, tacky, or soft films
- C. Rotating the dial too fast when taking measurements
- D. Taking measurements too far from the edge of a surface
Answer: A,B,C
NEW QUESTION 53
......
Authentic Best resources for NACE-CIP1-001 Online Practice Exam: https://www.testbraindump.com/NACE-CIP1-001-exam-prep.html
Updates Up to 365 days On Developing NACE-CIP1-001 Braindumps: https://drive.google.com/open?id=11BCA766AsmtNn9tuNMC2kF1a0tT-krXL
